Skip to content

Product Guide

Electronics and Electricals
ProductDescriptionApplication
VpCI ® -105Cortec ® VpCI ® -105 emitters are unique devices designed to provide corrosion protection for metal components and parts enclosed in non-ventilated control boxes, cabinets, or tool boxes.Stick inside enclosures of up to 5 cubic feet (0.14 m³).
VpCI ® -111VpCI ® -111 emitters are unique devices designed to provide corrosion protection for metal components and parts enclosed in non-ventilated control boxes, cabinets, or tool boxes.Stick inside enclosures of up to 11 cubic feet (0.31 m³).
ElectriCorr ® VpCI ® -238A cleaner/protector for electrical/electronic equipment and components (e.g., circuit boards, electrical contacts, electric motors, generators, junction boxes). Forms a thin film of Vapor phase Corrosion Inhibitors. Does not alter the electrical resistance or magnetic properties of metal substrates. No CFC or 1,1,1-Trichloroethane.Spray a very light mist over area needing protection. Dry time is approximately 1-2 hours at 70 °F (21 °C) and 50% relative humidity.
ElectriCorr ® VpCI ® -239A cleaner/protector for electrical/electronic equipment and components (e.g., circuit boards, electrical contacts, electric motors, generators, junction boxes) stored outdoors. Forms a thin film of Vapor phase Corrosion Inhibitors. Does not alter the electrical resistance or magnetic properties of metal substrates. No CFC or 1,1,1-Trichloroethane.Spray a very light mist over area needing protection. Dry time is approximately 1-2 hours at 70 °F (21 °C) and 50% relative humidity.
ElectriCorr ® VpCI ® -286Acrylic-based conformal coating designed to extend long-life performance of new and repaired electronic assemblies, especially in corrosive conditions such as high heat and atmospheric humidity.Spray a very light mist over area needing protection. Dry to touch in 5-10 minutes.
Corrosorber ®Corrosorber ® absorbs hydrogen sulfide and other corrosive gases. It will not interfere with VpCI ® protection but will instead absorb the gases that cause corrosion.Stick inside enclosure of up to 10 ft³ (0.28 m³). Replace when color changes from off-white to black.
Structural Steel
ProductDescriptionApplication
CorrVerter ®A fast drying, water-based one coat system (primer) that converts rusted surfaces to a hydrophobic passive layer and prevents further rusting through the unique formulation of chelating agents and PVC resins. User-friendly alternative to sand-blasting. Use alone or with topcoat for extended performance.Recommended DFT: 3.0-5.0 mils (75-125 microns).
VpCI ® -373A water-based wash primer for bonding other primers and coatings such as VpCI ® -386 and VpCI ® -395 to a variety of metal substrates.Prep surface to NACE #3 or SSPC SP2. Spray, brush, roll, or dip for 2.5 mils (62.5 microns) WFT and 0.5 mil (12.5 microns) DFT.
VpCI ® -384A solvent-based 2K urethane one coat system (topcoat) that provides protection in harsh, unsheltered applications. Excellent UV resistance.Recommended DFT: 1.5-3.0 mils (37.5-75 microns).
VpCI ® -386A fast drying, water-based acrylic one coat system (topcoat) that can be applied DTM (Direct to Metal) and provides protection in harsh, outdoor, unsheltered applications. VpCI ® -386 is weldable and can be used to keep surfaces corrosion-free prior to welding. Recommended DFT: 1.5-3.0 mils (37.5-75 microns).
VpCI ® -395A fast drying, 2K water-based epoxy one coat system (primer) that can be applied DTM (Direct to Metal) and provides protection in harsh, outdoor, unsheltered applications. Excellent for immersion type conditions. Can be used as topcoat indoors (away from UV light). Certified to meet ANSI/NSF Standard 61.Recommended DFT: 1.5-3.0 mils (37.5-75 microns).
VpCI ® -396A fast drying, solvent-based moisture cure urethane one coat system (primer and topcoat) that can be applied DTM (Direct to Metal) and provides protection in harsh, outdoor, unsheltered applications.Recommended DFT: 2.0-3.0 mils (50-75 microns).
VpCI ® -2026A 2K, solvent-based 100% solids novolac epoxy system (topcoat) that provides protection in harsh, outdoor, unsheltered applications.Recommended WFT/DFT: 11-13 mils (275-325 microns).
Concrete Structures
ProductDescriptionApplication
MCI ® -2005A water-based, organic, corrosion inhibiting admixture for protection of metallic reinforcement in concrete structures. Contains 67% USDA certified biobased content. Certified to meet ANSI/NSF Standard 61 for use in potable water structures. Meets all requirements of ASTM C1582. Earns credit toward LEED certification.Add MCI ® -2005 to concrete mix or repair mortars at 1 pt/yd³ (0.6 L/m³).
MCI ® -2005 NSNormal set (not delayed) version of MCI ® -2005. Certified to meet ANSI/NSF Standard 61. Biobased: 27%. Meets all requirements of ASTM C1582. Earns credit toward LEED certification.Add MCI ® -2005 NS to concrete mix at the rate of 1.5 pts/yd³ (1L/m³).
MCI ® -2006 NSA normal set, powder corrosion inhibiting admixture for protection of metallic reinforcement in concrete structures. Certified to meet ANSI/NSF Standard 61. Add to concrete mix at the rate of 1 lb/yd³ (0.6 kg/m³).
MCI ® -2018A 100% silane water repellent containing Migrating Corrosion Inhibitors (MCI ® ). Penetrates into concrete providing corrosion protection to reinforcing steel from carbonation, chlorides, and other contaminants. Certified to meet ANSI/NSF Standard 61. Also available as MCI ® -2018 V/O for easier application on vertical and overhead surfaces. Certified under EN 1504-2 (2+ system) for superficial protection of concrete.Apply by airless sprayer, roller, or brush. Approximate coverage rate is 125-175 ft²/gal (3-4.3 m²/L).
MCI ® -2019A 40% silane, solvent-based concrete sealer containing Migrating Corrosion Inhibitors (MCI ® ). Provides water repellency and delays/reduces corrosion. Certified under EN 1504-2 (2+ system) for superficial protection of concrete.Apply by airless sprayer, roller, or brush. Approximate coverage rate is 125-175 ft²/gal (3-4.3 m²/L).
MCI ® -2020A surface-applied Migrating Corrosion Inhibitor ™ designed to penetrate through cementitious materials including concrete, mortar, and limestone. Migrates in liquid and vapor phase to form a protective molecular layer on embedded reinforcement. Certified to meet ANSI/NSF Standard 61. Available in high viscosity MCI ® -2020 V/O version for vertical and overhead areas.Horizontal surfaces: Single coat at 150 ft²/gal (3.68 m²/L). Vertical surfaces: Two coats at 300 ft²/gal (7.36 m²/L).
MCI ® -2021A concrete sealer that combines a blend of reactive silicates, surface-active agents, and Migrating Corrosion Inhibitors (MCI ® ). Certified under EN 1504-2 (2+ system) for superficial protection of concrete.Approximate dosage: 150-250 ft²/gal (3.7-6.1 m²/L) for all coats combined.
MCI ® -2026 Floor CoatingA 100% solids, 2-component novolac epoxy coating designed for environments that require a high degree of chemical or temperature resistance.For optimum results, prime concrete floor first with MCI ® -2020 and MCI ® -2026. Apply at 250-300 ft²/gal (6.14-7.36 m²/L). Rougher and shot-blasted floors: 225-250 ft²/gallon (5.52-6.14 m²/L). Dry thoroughly before applying topcoat.
MCI ® -2241/MCI ® -2242A flexible, breathable water-proofing membrane based on a unique combination of acrylic emulsion, Portland cement, and fine fibers. Use to waterproof all types of above- or below-grade concrete and masonry.Apply only to sound and clean, dry, properly prepared frost-free surfaces in a 1/16 inch (1.6 mm) thick coat using a stainless-steel trowel or a spray device. Immediately trowel the product level.
MCI ® -2039A single-component, fiber-reinforced repair mortar containing Migrating Corrosion Inhibitors, fibers, and polymers. Provides a high level of adhesion, durability, and impermeability to water and carbonation attack.Mix 55 pound (25 kg) bag with 0.8-0.9 gallons (3.02-3.41 L) fresh water at 400-600 rpm for 3-5 minutes. One bag covers 12 square feet (1.11 m²) at 1/2 inch (12.7 mm) thick.
MCI ® -2701A single-component, polymer-modified, cement-based trowel-grade repair mortar designed for structurally repairing deteriorated concrete. Contains Migrating Corrosion Inhibitors to protect embedded steel rebar. Use on horizontal surfaces for repairs from 1/4 to 2 inches (6-51 mm) thick.Mix with 6-6.5 pints (2.83-3.08 L) water per 60 pound (27 kg) bag. One bag covers 20-25 square feet at 1/4 inch thick (1.9-2.3 m² at 6 mm thick).
MCI ® -2702A single-component, polymer-modified, cement-based repair mortar for structurally repairing deteriorated concrete. Specifically designed for vertical and overhead repairs from 1/4 to 2 inches (6-51 mm) thick.Mix with 6-6.5 pints (2.83-3.08 L) water per 50 pound (23 kg) bag. One bag covers 20-25 square feet at 1/4 inch thick (1.9-2.3 m² at 6 mm thick).
Process Equipment/MRO
ProductDescriptionApplication
VpCI ® -126High technology Vapor phase Corrosion Inhibitor film that protects metal objects from all types of corrosion including rust, tarnish, stains, white rust, and oxidation during storage or domestic and overseas shipments. Recyclable. Available in roll stock and bags.Use to package anything from small nuts and bolts to spares or large equipment on standby.
CorrLube ™ VpCI ® Lithium EP GreaseA lithium complex grease formulated with premium quality, severely hydrotreated base stock. Provides excellent resistance to oxidation and has high temperature stability. Suitable for operating and lay-up conditions.Apply to lubricating sleeves, bearings, fans, and other metal contact areas that require NLGI grade 2 grease by brushing, grease gun, or automatic application at a temperature range of -22 ° to 226 °F (-30 ° to 130 °C).
EcoLine ® Biobased Grease powered by Nano VpCI ® A multipurpose biobased grease with superior corrosion protection properties. Contains 86% USDA certified biobased content. Broad range of operating temperatures.Apply to metal-to-metal contact areas such as lubricating sleeves, ball and roller bearings, and vehicle/equipment chassis.
EcoLine ® 4320 & 4330
Add USDA biobased label
Heavy-duty green chemistry paint strippers designed to remove coatings, inks, and resins from metals, concrete, and wood surfaces. Contains 50% USDA certified biobased content. Includes flash rust protection. No California Prop 65 components that cause cancer, birth defects, or other reproductive harm.Apply by dip, brush, spray, or rolling. Allow to penetrate and soften coating before scraping off and/or pressure washing surface.
EcoLine ® Cleaner/DegreaserA heavy-duty, water-dilutable cleaner/degreaser for tough cleaning jobs in industrial and commercial applications. Ideal for cleaning machinery, shop tools, hoods, parts in-process, office equipment, floors, walls, and desks. Can be diluted up to a 1:20 ratio in water.
EcoLine ® ELPA high performance biodegradable soy-based lubricant and penetrant for general purpose use. Contains 95% USDA certified biobased content.Apply to metal parts for lubricating, loosening rusty bolts, cooling/lubricating basic metal cutting operations, or any other general lubrication need. Available in aerosol spray cans.
VpCI ® -422Environmentally-friendly biodegradable organic rust remover. Contains 92% USDA certified biobased content.Apply to rusty surface after removing loose rust; let stand for 10-15 minutes; rinse with an alkaline solution such as EcoLine ® Cleaner/Degreaser. Available in EcoAir ® air-powered spray cans.
VpCI ® -423Environmentally-friendly biodegradable organic rust remover for vertical or overhead surfaces. Contains 91% USDA certified biobased content.Apply to rusty surface after removing loose rust; let stand for 10-15 minutes; rinse with an alkaline solution such as EcoLine ® Cleaner/Degreaser. Available in EcoAir ® air-powered spray cans.
Natural Bioaugmentation for Enhanced Wastewater Treatment
ProductDescriptionApplication
BCP12An anaerobic digester that increases the efficiency of overloaded treatment systems by breaking down lipids, cellulose, lignin, proteins, and other complex organic molecules, mostly through hydrolysis and further through acidogenesis.Applied to the primary digester based on volume or flow rate. Contact Bionetix ® for dosage rates.
BCP22A blend of facultative anaerobic bacteria and free bacterial enzymes for use in treatment of fats, oils, and greases (FOG). Reduces foam, sludge, and grease build-up. Controls filamentous growth.Add water soluble pouches directly to the system. Contact Bionetix ® for dosage rates and application procedures.
BCP35MContains aerobic and facultative anaerobic bacteria and free bacterial enzymes specially selected to digest petroleum hydrocarbons with greater resistance to the effects of organic inhibitors present in wastewaters with a higher salt content.Apply to activated sludge systems, trickling filter beds and rotating biological contactors, and lagoons, etc. Contact Bionetix ® for dosage rates.
BCP50A blend of facultative anaerobic bacteria and free bacterial enzymes selected to biodegrade organic material in sewage wastewater. Helps reduce sludge and odors. Improves effluent and allows faster startup.Apply to activated sludge systems. Contact Bionetix ® for dosage rates.
BCP54TTablets containing facultative anaerobic bacteria and free bacterial enzymes, effective in aerobic and anaerobic conditions for biodegrading organic material comprised of proteins, fats, and carbohydrates. Reduces BOD, TSS, sludge, and odors. Improves overall water quality.Apply to lagoons based on surface area. Contact Bionetix ® for dosage rates.
BCP655A blend of bacteria that removes nitrogen (i.e., amino acids, proteins, purines, pyrimidines, nucleic acids) from wastewater rather than converting it to another form. BCP655 helps reduce ammonia levels, reduce plant upsets, and increase treatment efficiency by at least 50%. This helps eliminate expensive surcharges due to high TKN discharge levels. Apply to lagoons based on surface area. Contact Bionetix ® for dosage rates.
BIOBLOC22A slow-release block containing different bacteria together with specialty penetrants and surfactants that loosen and liquefy heavy grease deposits, thereby assisting in their biodegradation. Helps reduce odors and grease buildup; keeps floats clean; prevents emergency blockages.Add BIOBLOC22 directly to grease traps. Five pound (2.3 kg) BIOBLOC22 lasts about one month in a 5,000 gallon (18,927 L) volume.

Copyright© 2018 Cortec Corporation. All Rights Reserved.